Project Description
Wholesale ECE 104 Reflective Tape Supplier – Conspicuity Tape Manufacturer
Quick Details Of ECE 104 Reflective Tape
- Product item: WL-3220
- Size: 5 cm * 45.7 m (customized)
- Durability: 5 years
- Surface film: PET/PC
- Color: White, Red, Yellow (customized)
- Application: ECE 104 R Reflective Tape Attached To Traffic Road Sign, Vehicle Stickers etc.
- Feature: Un-Tearable, Excellent Weatherablility, UV Printing
- Certification: E-Mark
- Samples: Samples are available free of charge
ECE R 104 Reflective Tape Product Description
1. What is ECE 104?
ECE 104 is a regulation that establishes guidelines for the use of retro-reflective safety markings on heavy goods vehicles operating throughout Europe.
Since July 2011, all newly registered HGVs over 7.5 tonnes and trailers over 3.5 tonnes operating in the UK, are required by law to be fitted with homologated retro-reflective markings. These must clearly outline the rear and sides of the vehicle to make it visible for up to 1000 meters in low light conditions. ECE104 specifies the standard for the reflective materials used and where and how it must be positioned on the vehicle or trailer.
These materials are divided into 3 categories.
- Category “C”: Profiling materials
- Category “D”: material for unique markings/graphics for limited areas
- Class “E”: material used for distinctive markings/graphics for extended areas, with Class “C” being the highest class in terms of reflectivity and Class “E” being the lowest.
2. Requirements of Vehicle Safety Markings for ECE104
Vehicle Safety Markings required under ECE104 must carry the “E-mark” to show that the tape has met the minimum requirements of the regulation. The markings need to be between 50mm to 60mm.
2.1 The Rear of The HGV Vehicle:
- 1.1 A complete contour line marking (box) needs to be applied if the rear of the vehicle is wider than 2100mm.
- 1.2 The conspicuity marking should be as close as practicable to the edge of the vehicle and should equate to at least 80% of the overall width of the vehicle.
2.2 Side of the vehicle:
There are two options to choose from, a complete contour line marking (box) or a partial contour marking (corner ticks).
- 2.2.1 Partial contour markings are the minimum requirement.
- 2.2.2 The conspicuity markings shall equate to at least 80% of:
– 2.2.2.1 The length of the vehicle (excluding the cab);
– 2.2.2.2 The length of the trailer (excluding the drawbar). - 2.2.3 The length of the upper corner marking tape must be a minimum of 250mm in each direction.
ECE 104 does not contain any detailed information on the practical application of magnetic tape on vehicles – this information can be found in Regulation 48.
3. Regulation 48
Regulation 48 contains the authorization of the markings of Regulation ECE 104 and sets out its conditions, i.e. the type of vehicle that must be complied with, the colors to be used, etc. In other words, all technical aspects relating to the use of adhesive tapes must be approved in accordance with the technical requirements of ECE 104.
3.1 Regulation 48 only covers conspicuity marking of category “C”
Since Article 48 deals with lighting and light signalling devices, categories “D” and “E” of ECE 104 are not included in or covered by this rule. The use of these materials is left to the competent national authorities. Previously, when ECE 104 contained application guidelines, it was required that graphics made with Category D or E materials be placed in complete outline markings. Today, this is not a requirement in Regulation 48, but a decision made at the national level. This means you need to check your own National Lighting Code.
4. WEALLIGHT’s ECE104 Reflective Tape
WEALLIGHT provides a series of reflective markings with mandatory E-Mark and all the tags that are in accordance with the ECE 104 regulations. All WEALLIGHT mark bands are divided into “C” levels, which means that they are the brightest mark allowed, they are easy to smear, resist exfoliation and other damage, and maintain brightness and color even in the worst working conditions.
To ensure that your truck/truck can be visible to other drivers at night or at low altitude, our series of bright tapes will ensure that your vehicle is more conspicuity to other road users, thereby reducing the chance of accidents.
With ECE 104 compliant conspicuity marking tape, you can have your truck up to snuff in just 20 minutes. Not only is tape your safest option, but it’s also very easy to apply and requires no special equipment. In fact, you can implement the app in your garage and have your own vehicle in action in as little as 20 minutes. At night, you can now see your vehicle from 1,000 meters above the ground.
4.1 ECE 104 Reflective Tape WL-32201
4.2 ECE 104R Reflective Tape WL-32202
Wholesale Conspicuity Reflective Tape Manufacturer & Supplier — WEALLIGHT
WEALLIGHT is a reflective tape manufacturer and the manufacturer of ECE 104 conspicuity marker tape, we have over 10 years of experience from safety marking to the transportation industry. Wholesale all kinds of reflective tapes, and accept OEM order.
Our main product including Reflective Tape With ECE 104 Standards, Conspicuity Tape, yellow reflective tape, reflective tape for vehicles, Highway Reflective Tape, best reflective tape, Striped Reflective Tape, Green Reflective Tape, Reflective Sticker Sheets, Outdoor Reflective Tape, Reflective Tape Wholesale, reflective conspicuity tape, Reflective Bumper Tape, Light Blue Reflective Tape, High Intensity Prismatic Tape, Boat Trailer Reflective Tape, Waterproof Reflective Tape, Reflective Road Signs Materials, Custom Reflective Signs, Reflective Tape Sheets, SOLAS Reflective Tape, Reflective Bumper Stickers For Cars, DOT C2 Reflective Tape, Fluorescent Yellow Green Reflective Tape, NTC 5807 Reflective Tape, Road Safety Reflective Stickers, Truck Rear Markers Plates, Bulk Reflective Tape, Pre-Cut Reflective Tape, Coast Guard Approved Reflective Tape, Checkered Reflective Tape, diamond grade reflective tape, DOT C2 Conspicuity Tape, Custom Reflective Bumper Stickers, Reflective Tape SASO 2913, Orange Reflective Vinyl, Metallized Reflective Tape, and so on.
We also accept custom printed reflective tape with company logo. Contact us to know more details, today!
Conspicuity Tape
Green Reflective Tape
Outdoor Reflective Tape
Light Blue Reflective Tape
Waterproof Reflective Tape
Custom Reflective Signs
ECE 104 Reflective Tape Of Shipment & Payment
- Sample: 1-2 days without logo printed, 3-7days with logo printed
- Bulk lead time: 3-15 days more or less, based on your quantities
- Supply capacity: 10000 Roll/Rolls per Day
- Mode of transport: Sea, road, air, express
- Delivery: FOB XIAMEN, CNF, CIF, Door to Door
- Terms of payment: T/T, L/C at sight, Western Union, Paypal
You are most concerned about the problem
1. Q: Are you a manufacturer or trading company?
A: Our company is a manufacture specializing in processing and marketing kinds of reflective materials with our own factory.
2. Q: Do you offer a free sample?
A: Of course, we can offer a small free sample for you.
3. Q: What is the delivery time?
A: Usually 5-15 working days, According to the order quantity.
4. Q: What are the payment terms?
A: We can accept T/T, L/C, Western Union, Paypal, etc.
5. Q: What’s your MOQ?
A: We can accept small order first to check the quality.
6.Q: What’s ECE 104?
A: ECE 104 is a new mandatory conspicuity marking legislation that comes into force on 10th July 2011.
ECE 104 Regulation Implementation Date, July 10, 2011
What happened to ECE 104 on July 10, 2011?
By implementing the Lighting Regulation 48-03, the EU has made the ECE 104 Category C conspicuity marking mandatory*. the WEALLIGHT ECE 104 Reflective Tape range has been specifically designed to meet this new requirement.
Since 10 July 2011, the use of conspicuity marking is mandatory for new trucks with a maximum tonnage of more than 7.5 tonnes (N2 and N3) and trailers with a tonnage of more than 3.5 tonnes (O3 and O4). ).
The requirements of 10 July 2011 are contained in a revised version of the Lighting Directive 76/756 (Directive 2007/35), which governs the installation of lighting and signaling equipment on motor vehicles in the EU. Directive 2007/35 specifies this date in Article 2 below
Article 2
From 10 July 2011, if a Member State fails to comply with the requirements set out in Directive 76/756 / EEC as amended by this Directive for reasons relating to the installation of lighting and signaling devices, it shall be taken into account that its accompanying new car conformity certificate in accordance with Directive 70/156 / EEC is no longer valid, Article 7 of that Directive for the purpose (1).
In order to clarify the requirements that need to be met by automotive OEMs before 10 July 2011, Directive 2007/35 has also been clarified in parameter 5.3 Reference is made to the following series of amendments to Regulation 48, 03 published in EU journals.
(3) In order to take account of the further amendments to UN/EEC Regulation 48(3) already voted by the Community, Directive 76/756/EEC shall be adapted to the requirements of this UN/EEC Regulation by adapting it to technical progress. For the sake of clarity, Annex II of Directive 76/756/EEC should be replaced.
Like in any Directive, there is also a requirement given in Article 3 for all members of the EU to transpose and publish the text of this Directive for reasons of notice and transparency by 9 July 2008 in their national RVLR regulations.
Application Of ECE 104 Reflective Tape
ECE 104 conspicuity tape requirements: Since July 2011, ECE 104 has stipulated that all newly registered over 7500 kilograms of heavy trucks and more than 3500 kilograms of trailers should have reflective markings, clearly outline the rear and side sides of vehicles, so as to improve their visibility.
ECE 104 regulation also provides for the standard of reflective material used and the position it must be on the vehicle or trailer. But even before ECE 104, team managers usually use a reflective marking on vehicles. Many fleet managers realized that reflective marking on vehicles helps prevent accidents, save lives, reduce vehicle downtime and maintenance, protect employees on roads and car factories, and provide customers with a more professional image.
Retroreflective Material Sheeting Tape Manufacturing Factory Company – WEALLIGHT
WEALLIGHT is a Reflective Material Manufacturer and reflective tape wholesalers, specializing in the processing and sale of various reflective materials with its own factory. We have a strong R & D capability, the product not only solves the traffic safety problem but also widely used in shoes, clothing, bags, and other fashion areas.
Contact us to get a free sample of ECE 104 Reflective Tape, and inquiry wholesale pricing of Conspicuity Tape, Now!
Marking of Different Vehicle Types
On most European trucks, semi-trailers and trailers, it is easy to apply ECE 104 compliant eye-catching markings; this means that it is easy to find the right place on the vehicle where the tape should be applied, and the application itself is not complicated.
However, on some vehicles, imagining where or how to get the eye-catching tape to make the vehicle compliant can be trickier. Therefore, we’ve created an overview of some of the most common vehicle types and provided guidelines on where to apply the tape.
Please note that these are only guidelines and if in doubt, you should always consult your local authority. WEALLIGHT cannot be held responsible for any applications that fail to comply.
1. Car Transporters
Can you mark car transporters?
The answer is yes!
With car carriers, the sides are usually easier to mark with horizontal lines. In most cases, top corners are not possible.
The rear is more complex, but the solution can be to mark the vertical and upper horizontal lines on the rear profile. If the vehicle construction makes marking impossible due to lack of width, there is the option of riveting to the aluminum frame at the corners (see photo) and applying an eye-catching tape to it.
2. Concrete Mixers
Can you mark concrete mixers?
The answer is yes!
Working on the side of a concrete mixer is not easy, but it can be covered by 40% or more with special fittings. In most cases, it is helpful to use a corner aluminum frame (see photo) to rivet it to the vehicle. The tape is then applied to the frame.
The rear can usually be marked with a line marker.
3. Skeletal / Container Chassis
Can we mark skeletal constructions?
The answer is yes!
Application on skeletal constructions (container chassis) is not easy, but according to special vehicle regulations, at least 40% of the sides are usually covered. Usually, it is easy to apply on a 20-foot container carrier and more difficult to apply on a large 40-foot container carrier.
Usually, the rear of the vehicle is OK.
4. Curtain Siders
Can curtain siders be marked?
The answer is Yes!
Application on curtains/tarpaulins is easy. The WEALLIGHT ECE104 Curtain grade tape has been made with a vinyl construction, which allows a sufficient degree of flexibility to follow the flexing and movements of the curtain. The tape comes with either a standard pressure-sensitive adhesive on the back (clean the surface, stick it on!), or a heat-activated adhesive.
The curtain grade tapes are available both as continuous strips or in a segmented version.
A great deal of curtain siders has a rigid structure to the rear. In that case, you should choose a conspicuity tape designed for this type of application.
5. Hook Lifts
Can hook lift be marked?
The answer is Yes!
Although the application of conspicuity markings is not easy on all hook lifts, it is usually possible to cover at least 40% as per the special application authorization. In most cases, a significantly larger percentage can easily be covered.
On the structure above the wheels, it may be necessary to re-apply the conspicuity marking tapes to an aluminum frame which is then riveted onto the vehicle.
6. Special Vehicles
Can Special Vehicles be marked?
The answer is in most cases Yes!
The category ‘Special Vehicles’ covers a lot of different vehicle types, and indeed some of these can be more tricky or indeed impossible to apply the conspicuity markings too. However, the majority of these applications are possible.
6.1 Road Sweepers
In the UK and some other countries, road sweepers are equipped with chevron markings to the rear. ECE 104 conspicuity markings can indeed be applied to the rear of these as well. Regulation 48 states that “additional retroreflective devices” can be applied to a vehicle as long as they don’t obscure mandatory devices fit to comply with Regulation 48. In the case of the Chevron, which would be treated as “additional”, it will not obscure the ECE 104 tape as long as it is applied to the inside of the bumper and as long as the mounting height of tape on the vehicle above the ground is equal or more than 250mm.
6.2 Timber Transporters
Some timber transporters have a rigid structure, which makes side and rear marking possible – either directly on the structure, or pre-applied to an aluminum frame. However, for the timber transporters without a bottom structure going to the edge of the vehicle, the application is not considered possible.
7. Flat Bed Trailers
Can the Flat Bed Trailer be marked?
The answer is Yes!
Application on flatbed trailers is quite easy. You do the marking as a line marking, both to the side and to the rear. Upper top corners are not possible due to the trailer construction.
8. Tankers
Can it be marked?
The answer is Yes!
In most cases application on tankers is easy. For the curved rear outline, WEALLIGHT has designed a special version of the pre-cut reflective tape, which we call Pre-cut Tanker Stickers. This product is supplied in a continuous roll, where you peel off pre-cut individual labels (each 16 cm long) which are then easily applied to the vehicle. It is recommended that you start your application by marking the 4 ‘corners’ (top / 90 degrees / 180 degrees / 270 degrees). You then measure the open space between 2 pieces and calculate how much space you will have between each additional piece.
9. Refrigerated Trailers
Can refrigerated trucks be marked?
The answer is Yes!
Application on refrigerated trucks is easy with WEALLIGHT ECE 104 R Tape.
10. Tippers
Can it be marked?
The answer is Yes!
The application of conspicuity marking tapes to tippers is easy.
11. Rigid Bodies
Can the vehicle body be marked?
The answer is Yes!
Application on rigid vehicle bodies is easy with WEALLIGHT ECE104 Tape. The tape comes with a normal pressure-sensitive adhesive.
12. Refuse Trucks
Can refuse truck be marked?
The answer is Yes!
Application on refuse trucks is easy with WEALLIGHT ECE 104 Rigid Grade Tape.
Need a Hand?
If you’re not sure where to attach the marker tape to a specific vehicle, send us a photo of the vehicle and let us work with you to find the best solution.
Contact us today! (Our E-Mail: [email protected]; WhatsApp/Skype: +86 18659739121)
Note: The examples provided in this section are for guidance only. WEALLIGHT recommends that you always liaise with your local authority to ensure 100% compliance with the placement of the prominent marking tape on your vehicle.
Side Markings
Local outline markings for vehicles exceeding 6,000 mm in length fall into the following categories.
- Maximum mass over 7.5 tonnes for N2, maximum mass for N3 (except for chassis cabs, incomplete vehicles, and semi-trailer tractors)
- O3 and O4
The mandatory local contour markings may be replaced by full-contour markings.
Retro-reflective marking strips must be in accordance with ECE 104 “C” category.
Rear Marking
(a) Complete rear-end profile markings on vehicles exceeding 2,100 mm in width, in the following categories.
Trucks: N2 and N3 with a maximum mass of more than 7.5 tons (chassis cabs, incomplete vehicles, and semi-tractors excepted).
Trailer: o3 and o4 However, line markers may be installed if shape construction, design, or operational requirements preclude the installation of forced contour markers.
Retro-reflective marker strips shall be in accordance with ECE 104 “C” category.
Side Markings
At least 80% of the length of the vehicle (not including the length of the cab) must be marked. This can be reduced to 60% for difficult applications and 40% for exceptionally difficult applications.
The lower line of the marking tape must be placed at least 250 mm from the ground and not more than 1500 mm in height. It can be extended to 2500mm in special cases.
The length of the upper corner markers must be at least 250 mm. the upper corner markers should be placed as high as possible but within 400 mm of the upper end of the vehicle.
Where it is not possible to apply the top corner markings for structural reasons of the vehicle, it is permitted to apply separate line-markings.
Complete contour markings are required at the rear unless this is not possible for structural reasons of the vehicle.
The maximum height requirements for the lower horizontal line are the same as those for the side markings (see above).
Which Colors of ECE 104 Conspicuity Tape Should You Use?
Yellow. Can be used on the side and/or rear.
Red. Can be used at the rear.
White. Available for side
*) Note: Special marking requirements for Poland and Ireland.
- Poland. Only yellow in the back.
- Ireland. Only red to the back.
It is always advisable to consult with the state road administration to find out the special requirements of the state for the use of colors.
How To Be Sure That Reflective Tape Is ECE 104 Certified
You want to mark your HGV with reflective tape, but how can you be sure that the reflective tape you bought has actually been approved?
There are many reflective strips on the market, which vary greatly in quality and price. Many reflective strips are 50 mm wide and come in the new law’s yellow, red and white colors.
But that’s not enough! The key is to look for the so-called “E-Mark” – a mark that is permanently printed on approved reflective tape at least every 50 centimeters.
How does a tape manufacturer obtain an E-Mark?
In order to receive the approval mark, retro reflective tapes must meet all of the minimum requirements of the regulations. This means that, as a user, you can be sure of the tape’s performance, including reflectivity, correct color, durability in all weather conditions, and more. Approved tapes are extensively tested at a European approved testing facility and only those tapes that pass all tests are awarded the E mark.
C:
This means that it is certified as a Class C under the 104 regulations.
Grade C is the correct grade for line/contour marking tapes.
E+ Number
This indicates the country in which the tape was certified by the testing agency. For example, E4 means that the tape was certified at a facility in the Netherlands.
104 R+ Number
104 R indicates that the tape was approved under the ECE 104 regulation. The last digit is the actual approval number of the tape.
What exactly do the elements in the E-mark mean?
Certified tapes display an E-Mark, which is the same or similar to the markings in our product pictures. (This specific mark applies to ECE 104 tapes, approved for rigid surfaces).
So make sure that the tape you buy for your truck comes with an e-mark; this is not only a guarantee of quality and high performance but also a guarantee that you are complying with the law.
Being Seen is Being Safe
The ECE104 guide provides improved road safety through visibility and improves legibility and visibility at night, which is good news for drivers and their vehicles. Since July 2011, all commercial vehicles have been required to be fitted with eye-catching reflective signage tape. The life-sustaining measures are an important step in further reducing the risk of accidents and making road transport safer.
One of the main objectives of marking HGVs with reflective tape is to reduce the number of accidents in low-light conditions involving trucks and trailers. Led by Italy, Romania, Poland, and Slovakia, the signage belts became mandatory in Germany and many other countries in July 2011. The ruling applies to all newly registered commercial vehicles of 7.5 tonnes and above, as well as trailers of 3.5 tonnes and above. Reflective materials must now be applied to the side and rear of all relevant vehicles in accordance with UNECE Regulation ECE 48-03. The move finally acknowledges that marking tape can significantly reduce the number of accidents involving long articulated vehicles and trucks – something that has been proven in a number of investigations, including the European Darmstadt study. For ORAFOL, it is important to combine safety with user requirements to maximize customer benefits.
A number of studies have been conducted documenting the positive effects of conspicuity marking, and the NHTSA study estimated that the potential reduction in the above types of accidents would be no less than 41%.
You May Like
DOT C2 Reflective Tape
SOLAS Reflective Tape
Truck Rear Markers Plates
Checkered Reflective Tape
DOT C2 Conspicuity Tape